Citizendia
Your Ad Here

Good quality track ballast is made of crushed stone. The sharp edges help the particles interlock with each other.
Good quality track ballast is made of crushed stone. Crushed stone or angular rock is a form of Construction aggregate, typically produced by mining a suitable rock deposit and breaking the removed rock down to the desired The sharp edges help the particles interlock with each other.

Track ballast forms the trackbed upon which railroad ties (US) or railway sleepers (UK) are laid. A railroad tie, cross tie, or railway sleeper is a rectangular object used as a base for Railroad tracks. It is packed between, below, and around the ties. [1] It is used to facilitate drainage of water, to distribute the load from the railroad ties, and also to keep down vegetation that might interfere with the track structure. Drainage is the natural or artificial removal of surface and sub-surface water from a given area Vegetation is a general term for the plant life of a region it refers to the Ground cover provided by plants [1] This also serves to hold the track in place as the trains roll by. It is typically made of crushed stone, although ballast has sometimes consisted of other, less suitable materials. Crushed stone or angular rock is a form of Construction aggregate, typically produced by mining a suitable rock deposit and breaking the removed rock down to the desired The term "ballast" comes from a marine shipping term for the stones used to weigh down a ship. [1]

Contents

Material properties

A good ballast should be strong, hard-wearing, stable, drainable, easy to clean, workable, resistant to deformation, easily available, and reasonably cheap to purchase. [2] Early railway engineers did not understand the importance of quality track ballast; they would use cheap and easily-available materials such as ashes, chalk, clay,[3] earth, and even cinders from locomotive fireboxes. A cinder is a pyroclastic material Cinders are extrusive Igneous rocks Cinders are similar to Pumice, which has so many cavities and is such low-density [4] It was soon clear that good-quality ballast made of rock was necessary if there was to be a good foundation and adequate drainage. In Geology, rock is a naturally occurring aggregate of Minerals and/or Mineraloids The Earth's outer solid layer the ‘ Lithosphere Drainage is the natural or artificial removal of surface and sub-surface water from a given area [3]

Good quality track ballast is made of crushed natural rock with particles between 28mm and 50mm in diameter;[5] a high proportion of particles finer than this will reduce its drainage properties, and a high proportion of larger particles result in the load on the ties being distributed improperly. [5] Angular stones are preferable to naturally rounded ones, as these interlock with each other, inhibiting track movement. The angular is a large Bone in the lower Jaw of Amphibians, Birds and Reptiles, which is connected to all other lower jaw bones the Erosion is the carrying away or displacement of solids ( Sediment, Soil, rock and other particles usually by the agents of currents such as wind [5][1] Soft materials such as limestone are not particularly suitable, as they tend to degrade under load when wet, causing deterioration of the line; granite, although expensive, is one of the best materials in this regard. Limestone is a Sedimentary rock composed largely of the Mineral Calcite ( Calcium carbonate: CaCO3 Granite (ˈɡrænɪt is a common and widely occurring type of intrusive, Felsic, igneous rock. [5]

In the early days of railroads in the United States, much material for ballast came from rock found in the local area. In the Midwest, for example, much use was made of quartzite, while states in the southeast, such as Florida, made use of limestone. Quartzite (from German Quarzit) not to be confused with the Mineral Quartz, is a hard Metamorphic rock which was originally Limestone is a Sedimentary rock composed largely of the Mineral Calcite ( Calcium carbonate: CaCO3 One specific type of quartzite used in the Midwest earned the name "Pink Lady" due to its color;[6] in other areas, the ballast can be a mix of light and dark colors called "Salt and Pepper".

Construction

The thickness of a layer of track ballast depends on the size and spacing of the ties, the amount of traffic expected on the line, and various other factors. A railroad tie, cross tie, or railway sleeper is a rectangular object used as a base for Railroad tracks. [1] Track ballast should never be laid down less than 150 mm (6 inches) thick;[5] high-speed railway lines may require ballast up to half a metre (20 inches) thick. [7] An insufficient depth of ballast overloads the underlying soil; in the worst cases, this can cause the track to sink. Soil, often typeset as SOiL, is a four piece rock band from Chicago Illinois United States founded by Shaun Glass Tom Schofield Tim King and Adam Zadel [8] If the ballast is less than 300 mm (12 inches) thick, this can lead to vibrations, which can damage nearby structures (though increasing the depth beyond this has no measurable effect). [9]

Track ballast typically sits on a layer of sub-ballast; the latter is typically made of small crushed stones. It gives a solid support for the top ballast, and seals out water from the underlying ground. [1] Sometimes, an elastic mat is placed under the ballast layer as well; this can allow for significant reductions in vibration. Vibration refers to mechanical Oscillations about an equilibrium point. [9]

It is essential for ballast to be piled as high as the ties, and for a substantial "shoulder" to be placed at their ends;[5] the latter being especially important, since this ballast shoulder is, for the most part, the only thing restraining lateral movement of the track. [10] The ballast shoulder should be at least 150 mm (6 inches) wide under any circumstances, and may be as large as 450 mm (18 inches). [11]

Maintenance

New track ballast is placed at the Boxmeer railway station, The Netherlands.
New track ballast is placed at the Boxmeer railway station, The Netherlands. Boxmeer ( is a Municipality and a town in the southern Netherlands.
A ballast regulator shaping newly placed ballast
A ballast regulator shaping newly placed ballast

If ballast is badly fouled, the clogging will reduce its ability to drain properly; this, in turn, causes more debris to be sucked up from the sub-ballast, causing more fouling. A ballast regulator is a piece of Rail transport Maintenance of way equipment used to shape and distribute the gravel Track ballast that supports the [12][7] Therefore, keeping the ballast clean is essential.

It is not always necessary to replace the ballast if it is fouled, nor must all the ballast be removed if it is to be cleaned. Removing and cleaning the ballast from the shoulder is often sufficient, if shoulder ballast is removed to the correct depth. [13][14] While this job was historically done by manual labour,[14] this process is now, like many other railway maintenance tasks, a mechanised one,[15] with a chain of specially-designed railroad cars handling the task. Mechanization or mechanisation ( BE) is providing human operators with machinery to assist them with the physical requirements of work A railroad car or railway carriage is a Vehicle on a rail transport system (railroad or railway that is used for the carrying of Cargo or One wagon cuts the ballast and passes it via a conveyor belt to a cleaning machine, then the cleaning wagon washes the ballast, and deposits the dirt and ballast into other wagons for re-use or disposal, respectively. A belt conveyor consists of two or more Pulleys with a continuous loop of material - the conveyor belt - that rotates about them [13] Such machines can clean up to two kilometres of ballast in an hour. [16]

Cleaning, however, can only be done a certain number of times before the ballast is damaged to the point that it cannot be re-used; furthermore, track ballast that is completely fouled can not be corrected by shoulder cleaning. [17] In such cases, it is necessary to replace the ballast altogether. One method of "replacing" ballast, if necessity demands, is to simply dump fresh ballast on the track, jack the whole track on top of it, and then tamp it down;[14] alternatively, the ballast underneath the track can be removed with an undercutter, which does not require removing or lifting the track. [17]

Regular inspection of the ballast shoulder is important;[5] as noted earlier, the lateral stability of the track depends upon the shoulder. The shoulder acquires some amount of stability over time, being compacted by traffic; maintenance tasks such as replacing ties, tamping, and ballast cleaning can upset this stability. After performing these tasks, it is necessary for either trains to run at reduced speed on the repaired routes, or to employ machinery to compact the shoulder again. [18][19]

If the trackbed becomes uneven, it is necessary to pack ballast underneath sunk ties to level the track out again. This is, in the mechanized age, usually done by a ballast tamping machine. A ballast tamper or tamping machine is a machine used to pack (or Tamp) the Track ballast under Railway tracks to make the tracks more durable A more recent, and probably better,[7] technique is to lift the rails and ties, and to force stones, smaller than the track ballast particles and all of the same size, into the void. This has the advantage of not disturbing the well-compacted ballast on the trackbed, as tamping is likely to do. [20] This technique is called pneumatic ballast injection (PBI; or, less formally, "stoneblowing"[21]). However, this technique is not as effective with fresh ballast, as the smaller stones tend to move down between the larger pieces of ballast. [16]

References

  1. ^ a b c d e f Solomon 2001, p. 18.
  2. ^ Hay 1982, pp. 409-410.
  3. ^ a b Bonnett 2005, p. 59.
  4. ^ Solomon 2001, p. 60.
  5. ^ a b c d e f g Bonnett 2005, p. 60
  6. ^ Solomon 2001, p. 19.
  7. ^ a b c Bell 2004, p. 396.
  8. ^ Hay 1982, p. 399.
  9. ^ a b Bachmann 1997, p. 121.
  10. ^ Hay 1982, p. 407.
  11. ^ 150 mm is considered an absolute minimum, and 300 mm (12 inches) being recommended for use in heavy traffic, or with continous welded rail or concrete ties. Most railways use between 300 mm and 400 mm (16 inches). A 450 mm shoulder significantly increases lateral stability and reduces maintenance effort, though little or no resistance to buckling is gained with a shoulder above this size. See Hay 1982, pp. 407-408; Kutz 2004 24. 4. 2.
  12. ^ Solomon 2001, p. 40.
  13. ^ a b Selig & Waters 1994, p. 1430.
  14. ^ a b c Solomon 2001, p. 41.
  15. ^ Institution of Civil Engineers 1988, p. 231.
  16. ^ a b IFSC #37, ch. 9.
  17. ^ a b Solomon 2001, p. 43.
  18. ^ Hay 1982, p. 408.
  19. ^ Kutz 2004, 24. 4. 2.
  20. ^ Anderson & Key 1999.
  21. ^ Ellis 2006, Pneumatic Ballast Injection, p. 265.

See also

External links

© 2009 citizendia.org; parts available under the terms of GNU Free Documentation License, from http://en.wikipedia.org
 Dapyx Software network: MP3 Explorer | Ebook Manager | Zenithic