A tent is a shelter consisting of sheets of fabric or other material draped over or attached to a frame of poles or attached to a supporting rope. A textile is a flexible material comprised of a network of natural or artificial Fibres often referred to as thread or Yarn. While smaller tents may be free-standing or attached to the ground, large tents are usually anchored using guy ropes tied to stakes or pegs. A guy-wire or guy-rope is a tensioned cable designed to add stability to structures (frequently ship masts, radio masts, Wind turbines, First used as portable homes by nomadic peoples, tents are now more often used for recreational camping and temporary shelters. Nomadic people, (from the νομάδες nomádes, "those who let pasture herds" also known as nomads, are communities of people that Definition Camping describes a range of activities Survivalist campers set off with little more than their boots whereas Recreational vehicle travelers arrive equipped

Tents range in size from one-person "bivouac" structures for a hiker to sleep in to huge (circus) tents capable of seating thousands of people. A circus is most commonly a traveling company of performers that may include acrobats, Clowns trained animals trapeze acts Hoopers, tightrope walkers The bulk of this article is concerned with tents used for recreational camping which have sleeping space for one to ten people. Larger tents are discussed in a separate section below.

Tents for recreational camping fall into two categories. Tents intended to be carried by backpackers are the smallest, lightest, and most expensive type. Smaller tents may be sufficiently light that they can be carried for long distances on a touring bicycle, a boat, or even a person's back. A touring bicycle is a bicycle either specially designed for or modified to handle Bicycle touring. A boat is a Watercraft of modest size designed to float or plane on water and provide transport over it Backpacking (in US tramping, trekking, or bushwalking in other countries combines Hiking and camping in a single Some very specialised tents have spring-loaded poles and can be 'pitched' in seconds, but take somewhat longer to strike.

The second type are larger, heavier tents which are usually carried in a car or other vehicle. Depending on tent size and the experience of the person or people involved, such tents can usually be assembled (pitched) in between 5 and 25 minutes; disassembly (striking) takes a similar length of time. The military organisations of most nations use tents to temporarily house troops living and working under field type conditions.

Contents 1 History 2 Use 2.1 Traditional 2.2 Military 2.3 Recreational 2.4 Emergency 3 General considerations 4 Parts of a modern tent 5 Design factors 6 Shelters 7 Current tent styles 7.1 Rigid poles 7.2 Flexible poles 7.3 Inflatable airbeams 8 Older tent styles 9 Larger tents 10 Influence on building design 11 See also 12 References 13 External links

History

Use

Tents are used as habitation by nomads, recreational campers, and disaster victims. Tents are typically used as overhead shelter for festivals, weddings, backyard parties, and major corporate events. They are also used for excavation (construction) covers, industrial shelters.

Traditional

Tents have traditionally been used by nomadic people all over the world, such as Native Americans and the Bedouin. Nomadic people, (from the νομάδες nomádes, "those who let pasture herds" also known as nomads, are communities of people that For indigenous peoples in the United States other than Hawaii and Alaska see also Native Americans in the United States. The Bedouin, (from the Arabic (ar بدوي pl badū) are a desert-dwelling Arab Nomadic pastoralist, or previously Traditional tents are still very popular in the Middle East and are primarily manufactured in heavy canvas fabric.

Military

Armies all over the world have long used tents as part of their working life. An army (from Latin Armata "act of arming" via Old French armée) in the broadest sense is the land-based Armed forces Tents are preferred by the military for their relatively quick setup and take down times, compared to more traditional shelters. One of the worlds largest users of tents is the US Department of Defense. The United States Department of Defense ( DOD or DoD) is the federal department charged with coordinating and supervising all agencies and functions of the government The US Department of Defense has strict rules on tent quality and tent specifications. The most common tent uses for the military are: temporary barracks (sleeping quarters), DFAC buildings (dining facilities), Forward Operating Bases (FOBs), After Action Review (AAR), Tactical Operations Center (TOC), Morale, Welfare, and Recreation (MWR) facilites, and security checkpoints. Futhermore, most of these tents are set up and operated through the support of Natick Soldier Systems Center. ^[1]

Recreational

Camping is a popular form of recreation which often involves the use of tents. Definition Camping describes a range of activities Survivalist campers set off with little more than their boots whereas Recreational vehicle travelers arrive equipped A tent is economical and practical because of its portability and low environmental impact. These qualities are necessary when used in the wilderness or backcountry.

Emergency

Tents are often used in humanitarian emergencies, such as war, earthquakes and fire. War is an international relations Dispute, characterized by organized Violence between National Military units An earthquake is the result of a sudden release of energy in the Earth 's crust that creates Seismic waves Earthquakes are recorded with a Seismometer Fire is the heat and light energy released during a Chemical reaction, in particular a combustion reaction. The primary choice of tents in humanitarian emergencies are canvas tents, because a cotton canvas tent allows functional breathability while serving the purpose of temporary shelter.

At times, however, these temporary shelters become a permanent or semi-permanent home, especially for displaced people living in refugee camps or shanty towns who can't return to their former home and for whom no replacement homes are made available. A displaced person (sometimes abbreviated DP) is a person who has been forced to leave his or her native place a phenomenon known as Forced migration. A refugee camp is a temporary camp built by a government the United Nations, international organizations (such as the Red Cross) or NGOs to receive Shanty towns (also called Squatter camps or Favelas are settlements (sometimes illegal or unauthorized of impoverished people who live in improvised

Most global NGO's maintain an emergency stockpile of tents strategically placed all over the world to service their requirements.

General considerations

Tent fabric may be made of many materials including cotton (canvas), nylon, felt and polyester. Cotton is a soft staple Fibre that grows around the seeds of the cotton plant ( Gossypium sp Canvas is an extremely heavy-duty plain-woven fabric used for making Sails Tents Marquees Backpacks and other functions Overview Nylon is a Thermoplastic silky material first used commercially in a nylon- Bristled Toothbrush (1938 followed more famously by Felt is a non-woven cloth that is produced by matting condensing and pressing fibers Polyester is a category of Polymers which contain the Ester Functional group in their main chain Cotton absorbs water, so it can become very heavy when wet, but the associated swelling tends to block any minute holes so that wet cotton is more waterproof than dry cotton. Nylon and polyester are much lighter than cotton and do not absorb much water; with suitable coatings they can be very waterproof, but they tend to deteriorate over time due to a slow chemical breakdown caused by ultraviolet light. Ultraviolet ( UV) light is Electromagnetic radiation with a Wavelength shorter than that of Visible light, but longer than X-rays The most common treatments to make fabric waterproof are silicon impregnation or polyurethane coating. Since stitching makes tiny holes in a fabric, it is important that any seams are sealed or taped to block up these holes to retain waterproofness.

Rain resistance is measured as a hydrostatic head in millimetres (mm). This indicates the pressure of water needed to penetrate a fabric. Heavy or wind-driven rain has a higher pressure than light rain. Standing on a groundsheet increases the pressure on any water underneath. Fabric with a hydrostatic head of 1000 mm or less is best regarded as shower resistant, with 1500 mm being usually suitable for summer camping. Tents for year-round use generally have at least 2000 mm; expedition tents intended for extreme conditions are often rated at 3000 mm. Where quoted, groundsheets may be 5000 mm or more.

Many tent manufacturers indicate capacity by such phrases as "3 berth" or "2 person". These numbers indicate how many people the manufacturer thinks can be fit snugly into a tent with just sleeping bags. These numbers do not allow for any personal belongings such as luggage, inflatable mattresses, camp beds, cots, etc. nor do they allow for people who are of above average height. Checking the quoted sizes of sleeping areas reveals that several manufacturers consider that a width of 150 cm (5 feet) is enough for 3 people - snug is the operative word. Experience indicates that camping may be more comfortable if the actual number of campers is 1 or even 2 less than the manufacturer's suggestion.

Tents can be improvised using waterproof fabric, string, and sticks. This allows them to be easily built and moved.

Parts of a modern tent

There are three basic configurations of tents, each of which may appear with many variations:

Single skin (USA: single wall): Only one waterproof layer of fabric is used, comprising at least roof and walls. Waterproof or water-resistant describes objects unaffected by water or resisting water passage or which are covered with a material that resists or does not allow water passage To minimize condensation on the inside of the tent, some expedition tents use waterproof/breathable fabrics. Waterproof fabrics are usually natural or synthetic fabrics that are laminated to or coated in some sort of permanently Waterproofing material such as Rubber,

Single skin with flysheet: A waterproof flysheet or rain fly is suspended over and clear of the roof of the tent; it often overlaps the tent roof slightly, but does not extend down the sides or ends of the tent.

Double skin (USA: double wall): The outer tent is a waterproof layer which extends down to the ground all round. One or more 'inner tents' provide sleeping areas. The outer tent may be just a little larger than the inner tent, or it may be a lot larger and provide a covered living area separate from the sleeping area(s). An inner tent need not be waterproof. The double layer may provide some insulation. The term thermal insulation can refer to materials used to reduce the rate of Heat transfer, or the methods and processes used to reduce heat transfer

Components:

• A flysheet or rain fly (found only in double skin tents) is used to protect the inside of the tent from water. It is waterproof on the outside and also provides a surface to collect condensation on the inside. Waterproof or water-resistant describes objects unaffected by water or resisting water passage or which are covered with a material that resists or does not allow water passage Condensation is the change of the physical state of aggregation (or simply state of matter from gaseous phase into liquid phase Condensation then runs down the walls to the ground. When a flysheet is used, it is important that there be no contact with the inner tent it is protecting; this keeps the inner dry. 'Expedition' tents often have extra poles to help ensure that wind does not blow the two layers into contact.

• The inner tent comprises the main body of the tent. For double skin tents, the inner tent (often mesh) is not waterproof since it is protected by the rain fly. For single skin tents, the inner tent is often made of waterproof-breathable material that prevents liquid water from penetrating the inside of the tent, but still allows water vapour to be transported out.

• The vestibule is a floorless covered section located outside a tent entrance that is typically used for the storage of boots, packs, and other small equipment. They are often used for activities that cannot be performed within the tent itself, such as cooking or equipment cleaning. Vestibules may be included as a removable attachment or integrated into the tent itself.

• A groundsheet is used to provide a waterproof barrier between the ground and a sleeping bag. With double skin tents, the inner tents normally have a sewn-in groundsheet, but a separate flat groundsheet may be provided for any living area. With single skin tents, the groundsheet may be sewn in or separate. Normal practice with sewn-in groundsheets is for the groundsheet to extend some 15 cm (6 in) up the lower part of the walls (sometimes called a 'bathtub' arrangement); this copes with a situation where water seeps under the side walls of the tent. Separate groundsheets allow loadsharing when backpacking, and may make it easier to pitch and strike a tent, but they provide less protection against insects etc. getting into the sleeping area; also, if any part of a separate groundsheet protrudes from under the side walls, then it provides a ready path for moisture to flow into the tent.

• The poles provide structural support. Structure is a fundamental and sometimes Intangible notion covering the Recognition, Observation, nature, and Stability of They may be collapsible for easier transport and storage. Some designs use rigid poles, typically made of metal, or sometimes wood. The M acro E xpansion T emplate A ttribute L anguage complements TAL, providing macros which allow the reuse of code across Wood is hard fibrous lignified structural tissue produced as secondary Xylem in the stems of Woody plants notably trees but also shrubs Other designs use semi-rigid poles, typically made of fiberglass, or sometimes of special metal alloys. Fiberglass (also called fibreglass and glass fibre see Spelling differences) is material made from extremely fine Fibers of Glass. An alloy is a Solid solution or Homogeneous mixture of two or more elements, at least one of which is a Metal, which itself has Another pole type uses inflatable beams as the structural support.

• Stakes or pegs may be used to fasten the tent to the ground. Some are attached to guy ropes that pull outward on the poles and/or fabric to help shape the tent or give it additional stability. Others are used to anchor the bottom edge of the fabric to the ground. Pegs may be made of wood, plastic, or metal. A mallet may be needed to drive thicker pegs into the ground. A mallet is a type of hammer with a head made of softer materials than the Steel normally used in hammerheads so as to avoid damaging a delicate surface Skewer metal pegs consisting essentially of a length of thick wire with a hook on one end can usually be inserted by hand, except if the ground is very hard, but may not be as strong as more substantial pegs. Pegs used for guy ropes should not be driven vertically into the ground; instead for maximum strength they should be driven in at an angle so that the peg is at right angles to the guy rope attached to it. Lighter free standing tents may need some guy ropes and pegs to prevent them from being blown away.

• Air vents help reduce the effects of condensation. When people breathe, they expel quite a lot of water vapour. Breathing takes Oxygen in and Carbon dioxide out of the body Aerobic Organisms require oxygen to create energy via respiration, in If the outside of the tent is colder than the inside (the usual case), then this vapour will condense on the inside of the tent, on any clothing lying about, on the outside of a sleeping bag, etc. Hence ventilation helps to remove the vapour, although this may let in cold air.

• An optional tent footprint or groundsheet protector may be used. This is a separate flat groundsheet which goes underneath the main groundsheet, and is slightly smaller than that groundsheet. The intention is to protect the main groundsheet, especially when camping on rough terrain, since it is much cheaper to replace a separate footprint groundsheet than it is to replace a sewn-in groundsheet.

Design factors

Many factors affect tent design, including:

• Financial cost
• Intended use
  • Backpacking/tramping, lengthy duration for carrying the tent. Weight and size are the most crucial factors.
  • Touring, high frequency of pitching and striking the tent. Ease of pitching/striking the tent is important.
  • Static, staying at one campsite for a week or two at a time. A comfortable camping experience is the target.

• Camping season

A tent required only for summer use may be very different from one to be used in the depths of winter. Manufacturers label tents as one-season, two/three-season, three/four season, four season, etc. A one-season tent is generally for summer use only, and may only be capable of coping with light showers. A three-season tent is for spring/summer/autumn and should be capable of withstanding fairly heavy rain, or very light snow. A four-season tent should be suitable for winter camping in all but the most extreme conditions; an expedition tent (for mountain conditions) should be strong enough to cope with heavy snow, strong winds, as well as heavy rain. Some tents are sold, quite cheaply, as festival tents; these may be suitable only for camping in dry weather, and may not even be showerproof.

• Size of tent
  • The number and age of people who will be camping determines how big and what features the sleeping area(s) must have. A gazebo is a pavilion structure, often octagonal commonly found in Parks Gardens and spacious Public areas Gazebos are freestanding or
  • To allow for inclement weather, some covered living space separate from the sleeping area(s) may be desirable. Alternatively, cyclists on a camping trip may wish for enough covered space to keep their bicycles out of the weather.
  • To allow for sunshine, an awning to provide shade may not go amiss. Some tents have additional poles so that the fabric doorways can be used as awnings.
  • Internal height. Manufacturers quote the maximum internal height, but the usable internal height may be a little lower, depending on the tent style. Ridge tents have a steeply sloping roof so the whole height is rarely usable. Dome tents slope gently in all directions from the peak enabling nearly the entire height to be usable for a large portion of the tent. Tunnel tents have a good usable height along the center line. Frame and cabin tents have gently sloping roofs and near vertical walls. To fully evaluate the usable space in a tent, both the maximum wall height and slope must be considered. There are four useful heights used to evaluate appropriate tent height: lie down only, sit, kneel, stand. The exact heights at whch these apply depend on the heights of the campers involved; those over 182 cm (6 ft) are likely to have less choice of tents than those who are somewhat shorter. As a starting point, sitting height is often between 90 and 105 cm (3 ft to 3 ft 6 in), and kneeling height may be between 120 and 150 cm (4 ft to 5 ft). These different heights are useful for evaluating whether certain tasks, such as changing clothes, can be accomplished in the tent.

• Number of sleeping areas.

Larger tents sometimes are partitioned into separate sleeping areas or rooms. A tent described as viz-a-viz usually has two separate sleeping areas with a living area in between.

• Tent colour.

In some areas of some countries (e. g. Lake District in England), there may be restrictions as to what colour tents can be, thereby reducing the visual impact of campsites. The Lake District, also known as The Lakes or Lakeland, is a rural area in North West England. England is a Country which is part of the United Kingdom. Its inhabitants account for more than 83% of the total UK population whilst its mainland The best colors for low visibility are green, brown, or tans. It is important to check for any such restrictions.

• Setup effort.

Some styles of camping and living outdoors entails quick setup of tents. As a general rule, the more robust the tent, the more time and effort needed to set up and dismantle. The style of the tent also has a great impact on its ease of use.

Shelters

Shelters are not normally used for sleeping. Instead they may act as a store or provide shelter from sun, rain, or dew.

• A flysheet consists of a single rectangular sheet of material. Two opposite sides are held up in the middle by poles, or sometimes just a rope between conveniently placed trees. The tops of the poles are attached via guy ropes to pegs, in order to keep the poles upright. Additional guy ropes are attached to the lower edges to pull them outwards away from the poles.

• A Gazebo uses a framework of metal poles to support a roof. A gazebo is a pavilion structure, often octagonal commonly found in Parks Gardens and spacious Public areas Gazebos are freestanding or This structure provides a lot more usable space than does a flysheet, since the gently sloping roof allows for a reasonable amount of headroom even at the edges (like a frame tent). Because a gazebo is free-standing, it is often used as a shelter for a temporary shop at a fair or street market.

• Beach tents are often a simplified form of dome tent and provide a useful (relatively sand-free) place to temporarily store beach equipment, but are at most showerproof. Some beach tents use specially treated fabric which is opaque to ultra-violet light, and so provide some protection against sunburn. Maximum height is typically about 120 cm (4 ft), and they are usually not large enough for an adult to lie down in.

• Fishermen's tents are also modified dome tents, often with a projecting awning high enough to sit under, but sometimes with no closable doorway.

Current tent styles

With modern materials, tent manufacturers have great freedom to vary types and styles and shapes of tents.

• The poles effectively hold the tent in the required shape.
• Poles which dismantle for ease of transport are either colour-coded or linked by chain or cord, so there is little doubt as to which poles connect where.
• Relatively few guy ropes are needed (sometimes none).
• The exact positioning of any guy ropes is not too critical.

Rigid poles

Many tents which use rigid steel poles are free-standing and do not require guy ropes, though they may require pegs around the bottom edge of the fabric. These tents are usually so heavy (25 to 80 kg) that it takes a rather strong wind to blow them away.

• Frame tents are double-skin tents. They have a living area and one or more cotton/nylon/polyester inner tents. The outer tent is draped over a free-standing steel frame, and may be made of canvas or polyester (the latter often has a hydrostatic head of 3000mm, i. e. three season camping). The living area is generally at least as large as the sleeping area, and there may be a specific section with window and extra air vents for use as a kitchen. The walls are nearly vertical and are typically about 150 to 180 cm high (5 ft to 6 ft). The center of the gently sloping roof is often 210 cm (7 ft) high or more and provides reasonable headroom throughout. The smaller 2-person models were less than 3 metres square (10 ft), but these have largely been replaced by dome or tunnel tents. The larger 8-person models may exceed 5 metres (16 ft) in length and/or width.

• Cabin tents are single-skin tents used mainly in the USA. They often have nylon walls, polyester roof, and a polyethylene floor, plus an awning at one or both ends. With a hydrostatic head of only 1000 mm, they may best be considered as summer tents. Removable internal dividers allow the cabin to be split into 'rooms'. Sizes may range from 13 ft by 8 ft (2 rooms) up to 25 ft by 10 ft (4 rooms), with wall and roof heights similar to those of frame tents. There are three separate pole units, with each unit consisting of two uprights and a connecting ridge. These pole units support the centre and ends of the roof, and are usually outside the tent.

Flexible poles

Flexible poles used for tents in this section are typically between 3 and 6 metres long (10 and 20 feet). Cheap poles are made of tubes of fibreglass with an external diameter less than 1 cm (1/3 inch), whereas more expensive aluminium alloys are the material of choice for added strength and durability. Fiberglass (also called fibreglass and glass fibre see Spelling differences) is material made from extremely fine Fibers of Glass. WikipediaNaming For ease of transportation, these poles are made in sections some 30 cm to 60 cm long (1 to 2 ft), with one end of each section having a socket into which the next section can fit. For ease of assembly, the sections for each pole are often connected by an internal elastic cord running the entire length of the pole.

• Dome tents have a very simple structure and are available in a wide variety of sizes ranging from lightweight 2-person tents with limited headroom up to 6 or 9-person tents with headroom exceeding 180 cm (6 ft). These may be single wall, or single-wall with partial flysheet, or double wall. Depending on the pole arrangement, some models pitch outer-tent first, while others pitch inner-tent first. The former helps keep the inner tent dry, but the latter is easier to pitch.

The basic dome has a rectangular floor and two poles which cross at the peak; each pole runs in a smooth curve from one bottom corner, up to the peak, and then down to the diagonally opposite bottom corner. There are usually special fittings at each corner which fit into sockets at the ends of each pole - pole tension keeps everything in shape. The poles can run on either the inside or outside of the tent fabric. When located on the interior, poles are held in place by a variety of means including hook and loop style straps, clips, and other fastening hardware. Poles that are located on the outside of the tent fabric are attached via fabric pole sleeves or plastic clips. Dome tents do not require guy ropes and pegs for structural integrity as they are considered free-standing, but must be pegged down in high winds.

The basic dome design has been modified extensively, producing tents with three poles, tents with irregularly-shaped bases, and other unusual types. A common variation is to add a third pole between two adjacent corners; this is angled away from the tent and supports an extension of the flysheet, to give a porch/storage area.

• Tunnel tents may offer more usable internal space than a dome tent with the same ground area, but almost always need guy ropes and pegs to stay upright. These are almost always double wall tents. Sizes range from 1-person tents with very limited headroom up to 8 or 10-person tents with headroom exceeding 180 cm (6 ft). Tunnel tents have a low end profile making them great for high wind situations.

Possibly the first tunnel tent was that produced by Hayes Mountain Equipment, Australia in 1965 to the design of Barry Hayes. It was successfully tested by the Monash University Mountaineering Club on Mount Baw Baw, Victoria, where it withstood 70 mph winds. It was subsequently used during the construction of the Melbourne University Mountaineering Club dome hut on Mount Feathertop. (4)(5)

A basic tunnel tent uses three flexible poles, arranged as three parallel hoops, with tent fabric attached to form a tunnel. The most common designs have a sleeping area at one end and a porch/storage/living area at the other. Smaller designs may use only 2 poles and larger designs may use 4 poles; the latter may have a sleeping area at each end and a living area in the middle.

• Hybrid dome/tunnel tents are now common. One variation is to use a basic dome as the sleeping area; one or two hooped poles to one side are linked by a tunnel to the dome to provide a porch. Another variation is to use a large dome as the living area, with up to 4 tunnel extensions to provide sleeping areas.

• Geodesic tents are essentially dome tents with 2 or more extra poles which criss-cross the normal two poles to help support the basic shape and minimise the amount of unsupported fabric. A geodesic dome is an almost spherical shell structure based on a network of Great circles ( Geodesics lying approximately on the surface of a Sphere This makes them more suitable for use in snowy conditions and in strong winds. To help withstand strong winds they are rarely more than 120 or 150 cm high (4 to 5 ft).

• Single-hoop tents use just one flexible pole and are often sold as light-weight 1 or 2-person tents. These are the modern equivalent of older style pup tents, and have the same feature of somewhat limited headroom. Different styles may have the pole going either along or across the tent.

• The pop-up tent is a recent innovation [1]. This type of tent is equipped with built-in very flexible hoops so that when the tent is unpacked, it springs into shape immediately, and so is extremely easy to set up. Such tents are usually single-skinned and are generally aimed at the one-season or children's end of the market; their high flexibility makes them unsuitable for use in windy situations. After use the tent is packed down into a thick disc shape; for a two-man tent this would be roughly the size of a bodhrán. The bodhrán (ˈbɔːrɑːn or /ˈbaʊrɑːn/ plural bodhráns or bodhráin) is an Irish Frame drum ranging from 25 to 65cm (10"

Inflatable airbeams

Inflatable pole supports, also known as airbeams, serve as rigid structural supports when inflated but are soft and pliable when deflated. Much like a bicycle tube and tire, airbeams are often composed of a highly dimensionally stable (i. e. no stretch) fabric sleeve and an air-holding inner bladder. However, other airbeam constructions consist of coated fabrics that are cut and manufactured to its intended shape by a method such as thermal welding. Depending on the desired tent size, airbeams can be anywhere from 2-40 inches in diameter, inflated to different pressures. ^[2] High pressure airbeams (40-80 psi) that are filled by compressors are most often used in larger shelters, whereas low pressure beams (5-7 psi) are preferred for recreational use. ^[3] The relatively low pressure enables the use of a manual pump to inflate the airbeam to the desired level. Airbeams have the unique quality of bending, rather than breaking, when overloaded. Tents that use inflatable airbeams are structured almost identical to those that use flexible poles.

• Dome tents that use inflatable airbeam support are available in a variety of sizes ranging from lightweight 2-person to larger 6+ person shelters, and are virtually identical to the arrangement of flexible-pole supported dome tents. Beams are usually integrated into the tent shell such that they do not have to be reinserted every time setup occurs. Airbeams can be located on either the inside or outside of the tent shell. Similar to the pole-supported construction, airbeam supported dome tents are free standing but should be staked out with pegs and guyout lines to increase stability and strength.

• Tunnel tents are a common form of airbeam supported tents because their size can be easily modified by adding additional hoops. Military applications use this style of tent for a range of purposes including medical shelters, helicopter enclosures, and airplane hangars. ^[4] In these constructions, hoops are generally identical in size. In commercial airbeam supported tents, the hoops can be different sizes. Tunnel tents tend to withstand high winds well because of their low profile shape. However, the tents are not freestanding and must be anchored and guyed out securely.

Older tent styles

Most of these tent styles are no longer generally available. Most of these are single-skin designs, with optional fly sheets for the ridge tents.

All the tents listed here had a canvas fabric and used a substantial number of guy ropes (8 to 18). The guys had to be positioned and tensioned fairly precisely in order to pitch the tent correctly, so some training and experience were needed. This made these styles relatively unsuitable for casual or occasional campers. Pup tents might use wooden or metal poles, but all the other styles mentioned here used wooden poles.

• A pup tent is a small version of a ridge tent intended for 2 or 3 people. It usually has a rectangular floor of size ranging from 4 ft by 6 ft up to 6 ft by 8 ft, and ridge heights ranging from 3 ft up to 5 ft. The side walls are usually about 1 ft high. There are guy ropes for each pole, at each corner, and in the centre of each side, and these guy ropes help to maintain the required shape. Earlier versions had a single upright pole at each end, while later versions often have two poles at each end, arranged rather like an 'A' shape, in order to make access easier. Some models have a horizontal ridge pole joining the tops of the end poles to support the centre of the tent.

• A ridge tent can sleep 5 to 8 people. They usually have a rectangular floor of size ranging from 8 ft by 10 ft up to 10 ft by 16 ft, and ridge heights around 6 ft to 7 ft. The side walls are usually about 3 ft high. They normally have a single upright pole at each end with the tops joined by a horizontal ridge pole. Longer models might have an additional upright pole in the centre to help support the ridge pole. They often have two guy ropes at each corner, and guy ropes every 2 ft along the sides. If strong winds are expected then two additional storm guy ropes are attached to the top of each pole.

• A square centre-pole tent was often used for family camping in the first half of the 20th century. Despite the use of 9 poles and 12 guy ropes, such a tent could be pitched by an (experienced) family of four in some 10 to 15 minutes. These tents had a square floor of size ranging from 8 by 8 ft up to 15 by 15 ft. There were poles about 5 ft high at each corner and in the middle of each side, and a 10 ft or 12 ft pole in the centre - the walls were vertical and the roof was pyramid-shaped, so there was plenty of headroom over most of the tent.

• A Sibley tent (bell tent) had a circular floor plan some 10 ft to 15 ft across, a single central pole some 10 ft high, and walls about 3 ft high. The Sibley tent was a tent invented by Henry Hopkins Sibley and patented in 1856 (U Guy ropes were connected every 2 ft around the top of the walls - these had to carefully tensioned to hold the pole upright and keep the tent in shape.

Larger tents

These larger tents are seldom used for sleeping.

• "Party tents" or "marquees" are common for large wedding, fairs, and other gatherings. They are made from PE (polythene) or the better quality ones from PVC. 'DIY' marquees are available up to 20 feet (6m) wide. 30 to 150 feet (9m to 45m) widths are very expensive and require specialized equipment and skill to erect, so they must usually be rented. Many corporations own large (9m to 45m wide) marquee tents but have them installed and maintained by qualified professionals. Party tents are held down with tensioned ratchets and/or stakes. Sizes range from 10 x 10 feet (3m x 3m) to 150 x 400 feet (45m x 120m). Marquees / party tents are dramatic and very strong.
• Traditional Pole Marquees - consist of canvas and more recently PVC, under tension by means of centre poles, side poles and guy ropes which are attached to ground stakes hammered into soft surfaces only such as a lawn or field. Hand made of white cotton canvas, traditional poled marquees are more attractive but much less practical and versatile than aluminium frame marquees. The modern PVC traditional pole marquee was introduced due to the material being easier to clean than woven canvas and giving them a longer hire life span.
• Aluminium Frame Marquees - Aluminium frame tents have no centre poles or guy ropes, can be erected on any surface and adjacent to buildings or annexe tents. Much more stable and can span a much wider area over pools, flower beds or trees.

• A newer category of the Marquee/Party tents is the High Peak Frame Tents (known by several brand names like "frame & cable", "vista", "pinnacle", etc). These tents have the advantage of the pole tents with the high top, ease of installation, cleaner look, and fewer parts. They also have the advantage of the Frame Tents as they do not have support pole(s) on the inside of the tent that touches the ground. The high top look is accomplished by using a "floating pole", which is a pole that sits on cables that run across the tent interior from the top of the sides. Most tent manufactures are now making these tents and they come in a variety of sizes and shapes that can be joined together to meet the needs of unique space requirements.
• Marquee tents typically have interchangeable parts, which allow for a rental company to easily expand to larger sizes. Tents can be ordered in a variety of colours, however white is by far the most popular colour. Skylights can also be built into the fabric, which allow a greater amount of light to enter and is useful if walls are being used. Walls can also be ordered with clear vinyl windows in them.
• "Bail Ring Tents" are usually tents that are 100 to 150 feet (30m x 45m) wide and expandable to any length. They can be made from either vinyl or canvas. The purpose of the bail ring style is to raise an enormous amount of material "the tent" off the ground without using heavy machinery. Initially, the center poles are raised and guyed out to stakes after which the tent is spread out and connected to the bail ring using shackles. Once the outside of the tent is raised a crew of men can go under the tent and start raising the bail ring up the center pole using a system of pulleys. This style of tent is not as popular as it was in the past due to the advancement of forklifts and skidsteers. There was a time when even smaller tents 40 to 100 feet (12m to 30m) were often raised and set using a bail ring.

• The four Major golf tournaments have tents set up they are usually 40 x 40 feet (12m x 12m).

• Tents or marquees are often hired from specialist companies.

• A "Rub Hall" is a large tent used primarily as emergency warehousing.

• A circus tent usually has one or more oval or circular arenas surrounded by tiered seating which might accommodate thousands of people. A circus is most commonly a traveling company of performers that may include acrobats, Clowns trained animals trapeze acts Hoopers, tightrope walkers Nowadays such large tents are made of some artificial fibre (polyester or vinyl) and are often erected with the help of cranes. In earlier times it was common for the circus elephants to be used as a source of power for pulling ropes to haul the canvas into position.

Influence on building design

Tent design has influenced many large modern buildings, and such buildings have in turn influenced tent design. Tent-style tensile structures are used to cover large public areas such as sports arenas (example: Munich Olympic Stadium) and airports (example: Denver International Airport). A tensile structure is a Construction of elements carrying only Tension and no Compression or Bending. The Olympiastadion is a stadium located in Munich, Germany. Situated at the heart of the Olympiapark München in northern Munich the stadium Denver International Airport, often called DIA, is by land size at, the largest international Airport in the United States, and the second largest

See also

• Bender tent
• Bivouac sack
• Campsite
• Roof tent
• List of types of lodging
• Traditional tent types
  • Chum
  • Fly
  • Loue
  • Goahti
  • Lavvu
  • Pandal
  • Sibley tent
  • Tarpaulin
  • Tipi
  • Wigwam
  • Yurt

• Tensile architecture
• Architecture of Mongolia

References

4 Records of the Monash University Mountaineering Club 1968 5 Dr John Bennett Earth Sciences Flinders University South Australia

External links

• Backpacking Tents | Outdoor High Adventure
• Spadout Tents - Information and comparison of tents.
• Tents - A United Nations guide to the use and logistics of family tents in humanitarian relief.

---

© 2009 citizendia.org; parts available under the terms of GNU Free Documentation License, from http://en.wikipedia.org
Dapyx Software network: MP3 Explorer | Ebook Manager | Zenithic