A spinnaker is a special type of sail that is designed specifically for sailing off the wind from a reaching course to a downwind, i. Calshot Spit is a one-mile long Sand and Shingle bank located on the southern bank of the open end of Southampton Water, on the south coast A sail is any type of surface intended to generate Thrust by being placed in a Wind &mdashin essence a vertically-oriented Wing. Sailing is the art of controlling a Sailing vessel. By changing the Rigging, Rudder and dagger or centre board a Sailor manages the force Points of sail describes a sailing boat's course in relation to the wind direction e. with the wind 90°–180° off the bow. The spinnaker fills with wind and balloons out in front of the boat when it is deployed, called flying. It is constructed of very lightweight, usually nylon, fabric, and is often brightly colored. Overview Nylon is a Thermoplastic silky material first used commercially in a nylon- Bristled Toothbrush (1938 followed more famously by It may be optimised for a particular range of wind angles, as either a reaching or a running spinnaker, by the shaping of the panels and seams. The spinnaker is often called a kite, or a chute (as in cruising chute) because it somewhat resembles a parachute in both construction and appearance. A parachute is a device used to slow the motion of an object through an atmosphere by creating drag. This should not be confused with the spinnaker chute which is a hull fitting sometimes used for launching and recovering the spinnaker. A spinnaker is a special type of Sail that is designed specifically for Sailing off the wind from a reaching course to a downwind i
Contents |
Operation
A spinnaker is a type of airfoil and will generate lift, if it is flown at a reaching angle. An airfoil (in American English) or aerofoil (in British English) is the shape of a Wing or blade (of a Propeller, rotor In the context of a Fluid flow relative to a body the lift force is the component of the Aerodynamic force that is Perpendicular to the flow Since the lift and drag generated by the spinnaker both act to move the boat forward, the lift to drag ratio is unimportant. In Fluid dynamics, drag (sometimes called fluid resistance) is the force that resists the movement of a Solid object through a Fluid (a The goal then is to generate the maximum amount of lift possible with no consideration of drag. Because of this, running spinnakers have extreme amounts of camber, making them nearly hemispherical in form. Camber in Aerospace engineering, is the asymmetry between the top and the bottom curves of an Airfoil in cross-section "Globose" redirects here See also Globose nucleus. A sphere (from Greek σφαίρα - sphaira, "globe The large camber maximizes the drag. Reaching spinnakers have less camber as they operate partially with an airflow that generates lift.
A well designed spinnaker will have taut leading edges when filled; leading edges that curl in will both reduce the lift and risk a collapse of the spinnaker. A well designed spinnaker will also have a smooth curve when filled, with no bubbles or depressions caused by inconsistent stretching of the sail fabric. A textile is a flexible material comprised of a network of natural or artificial Fibres often referred to as thread or Yarn. Any deviations from a smooth curve will cause the airflow over the leeward side of the sail to separate, in a reaching spinnaker, causing a reduction in lift and reduced performance. Windward is the direction from which the wind is blowing at the time in question
When running downwind in heavy weather or when hit by a gust, with or without a spinnaker, there may be a tendency for a roll of increasing amplitude to build up, known as the death roll. Points of sail describes a sailing boat's course in relation to the wind direction In a Keel boat a death roll is the act of broaching to windward putting the Spinnaker pole into the water and causing a crash- gybe of the boom It has been shown that this is due to aerodynamic instability of bermuda rigs when running, which can be aggravated by gusts, waves, mainsail twist, daggerboard etc too far down, hull form, and the sailing equivalent of pilot-induced oscillation. The term Bermuda rig refers to a configuration of mast and Rigging for a type of Sailboat and is also known as a Marconi rig; this is the typical A daggerboard is a retractable Keel used by various Sailing craft Pilot-induced oscillation occurs when the pilot of an Aircraft inadvertently commands an often increasing series of corrections in opposite directions each an Excessive heel leads to loss of rudder effectiveness resulting the boat slewing round uncontrollably in the direction opposite to the direction of heel. This is known as broaching. sailboat broaches when its heading suddenly changes towards the wind due to Wind / Sail interactions for which hull hydrodynamic reactions cannot compensate Aerodynamic instability when running can be countered by easing the pole forward slightly and over-sheeting the spinnaker somewhat to stop it swinging from side to side, by reducing mainsail twist using the boom vang, and by skilfully trimming the mainsheet. A boom vang (US or kicking strap (UK is a line or piston system on a Sailboat used to exert downward force on the boom and thus control the shape Luffing carefully onto a broad reach may help to retain control, as can moving everyone's weight as far aft as possible. Points of sail describes a sailing boat's course in relation to the wind direction Reducing sail should be considered.
Types of spinnakers
There are two main categories of spinnakers, symmetric and asymmetric depending on whether a plane of symmetry exists for that particular sail. Asymmetric spinnakers operate more like a jib, generating lift from the side, rather than the top like a symmetric spinnaker. This makes asymmetrics a better choice on reaching courses than symmetric spinnakers, which excel when running. While a fully equipped racing boat might have a number of spinnakers, both symmetric and asymmetric, to cover all courses and wind conditions, cruising boats almost always use an asymmetric, due to the broader application and easier handling afforded by the asymmetric.
Symmetric Spinnakers
The symmetric one is the most classic type, running symmetrical alongside the boat controlled by lines known as a sheet and a guy running from the lower two corners of the sail. In Sailing, a sheet is a line ( Rope, Cable or Chain) used to control the moveable corner(s of a Sail. A guy is a term for a line ( Rope) attached to and intended to control the end of a spar on a sailboat The windward line, or guy, is attached to the corner called the tack of the sail, and is stabilized by a spinnaker pole. spinnaker pole is a Spar used in Sailboats (both Dinghys and Yachts) to help support and control a variety of Headsails, particularly The leeward (downwind) line is called the sheet. Windward is the direction from which the wind is blowing at the time in question In Sailing, a sheet is a line ( Rope, Cable or Chain) used to control the moveable corner(s of a Sail. It attaches to the clew of the spinnaker and is used to control the shape of the sail. In Sailing the parts of a Sail have common terminology for each corner and edge of the sail The spinnaker pole must be moved in each jibe, and is quite difficult for beginners to use. A jibe or gybe is a sailing maneuver where a Sailing vessel turns its Stern through the wind such that the wind direction changes from one side of the However, it can be sailed in all downwind wind directions.
Symmetric spinnakers when sailing across the wind (reaching) develop most of their lift on the forward quarter, where the airflow remains attached. When correctly set for reaching, the leading edges of a symmetric spinnaker should be nearly parallel to the wind, so the flow of air over the leading edge remains attached. When reaching, the sail camber allows only some attached flow over the leeward side of the spinnaker. On running the spinnaker is angled for maximum drag, with the spinnaker pole at right angles to the apparent wind. The symmetric spinnaker also requires care when packing, since the three corners must be available on the top of the packing.
Asymmetric Spinnakers
The asymmetrical spinnaker is a more recent approach to the spinnaker. Its modern-day origins may lie with the Sydney Harbour 18ft Skiffs and date from at least the late 1980s. Port Jackson, containing Sydney Harbour, is the natural harbour of Sydney Australia The 18ft Skiff is considered the fastest class of sailing skiffs The tack of the sail may be attached at the bow like a genoa but is frequently mounted on a bowsprit, often a retracting one. The bow (pronounced &mdashrhymes with how) is a nautical term that refers to the forward part of the hull of a Ship or Boat, The genoa or jenny was originally referred to as the 'overlapping jib' or the Genoa jib, being named after the city of Genoa as explained below The bowsprit, or boltsprit, of a Sailing vessel is a pole extending forward from the vessel's prow If the spinnaker is mounted to a special bowsprit, it is often possible to fly the spinnaker and the jib at the same time; if not, then the spinnaker will be shadowed by the jib, and the jib should be furled when the spinnaker is in use.
The asymmetric has two sheets, very much like a jib, but is not attached to the forestay along the length of the luff, but only at the corners. In Sailing, a sheet is a line ( Rope, Cable or Chain) used to control the moveable corner(s of a Sail. Unlike a spinnaker, the asymmetric does not require a spinnaker pole, since it is fixed to the bow or bowsprit. The asymmetric is very easy to jibe since it only requires releasing one sheet and pulling in the other one, passing the sail in front of the forestay. A jibe or gybe is a sailing maneuver where a Sailing vessel turns its Stern through the wind such that the wind direction changes from one side of the Asymmetrics are less suited to sailing directly downwind than spinnakers, and so instead the boat will often sail a zig-zag course downwind, gybing at the corners. An asymmetric spinnaker is particularly effective on fast planing dinghies as their speed generates an apparent wind on the bow allowing them to sail more directly downwind. Apparent wind is the wind experienced by a moving object Apparent wind in sailing In Sailing, the apparent wind is the actual flow of air acting upon a It is also particularly useful in cruising yachts in the form of a cruising spinnaker or cruising chute, where the ease of handling is important and it is less likely to be used with a bowsprit. Various types of asymmetrics exist, and a common nomenclature classifies them by code from 0 to 6. Codes 1, 3, and 5 are reaching sails, and codes 2, 4, and 6 are running sails; the code 0 is a hybrid of genoa and spinnaker, designed to work like a genoa but classified under racing rules as a spinnaker.
- Code 0 The code 0 asymmetric is a tight reaching sail, the most upwind capable of the asymmetrics. The luff is as straight as possible, and the sail is flatter than other spinnakers. Due to the flatness of the code 0, it is usually made with a wire luff for strength, and of a heavier, less stretchy fabric than normal for a spinnaker. Due to the tight luff and flat cut, the code 0 can be fitted for roller furling. Roller furling is a method of furling or Reefing wherein a Sail is rolled around a stay or rotating Spar.
- Code 1 The code 1 is a light air reaching sail, where the apparent wind angles at low speeds has a significant effect to create angles of less than 90 degrees.
- Code 2 The code 2 is a medium air running sail, used for apparent wind angles over 90 degrees.
- Code 3 The code 3 is a medium air reaching sail, used for apparent wind angles near 90 degrees.
- Code 4 The code 4 is a heavy air running sail, used in the heaviest winds normally expected.
- Code 5 The code 5 is a heavy air reaching sail, used in the heaviest winds normally expected.
- Code 6 The code 6 is a storm sail, for running in storm conditions.
Spinnakers for cruising boats are starting to be patterned after the roller furling code 0 racing spinnakers, as they provide the easiest handling. North Sails, for example, offers three gennaker sails, based on the racing code 0 asymmetrics, with different sizes and cambers for varying angles and wind speeds. Other manufacturers offer similar cruising code 0 designs under different names, such as the screecher and reacher for upwind and downwind use respectively.
Flying the spinnaker
Since they are only used on certain points of sail, raising and lowering the spinnaker is a task that is often performed while under sail. Due to the size of spinnakers (the spinnaker is often double or more the size of the mainsail) this can be a difficult operation, since the sail will immediately catch the wind.
Rigging the symmetric spinnaker
Typically the symmetric spinnaker is packed in its own bag, called a turtle, with the three corners on top for ready access. The clews (lower corners) are controlled by lines called sheets, which lead from the clews back to the stern of the boat, and serve to control the sail position. Symmetric spinnakers have the windward clew secured to a spinnaker pole which is attached to the mast and holds the windward edge of the sail in position. Lines that control the spinnaker pole are called guys. In small boats, a single line may serve as a combination sheet/guy. The head (top corner) is attached to the spinnaker halyard, which is used to raise the sail up the mast.
The spinnaker pole may be allowed to raise and lower with the force of the wind, or it may have lines attached to it to raise (the topping lift) and lower (the foreguy) the angle of the pole. If these lines are used, they are generally set up before setting sail, and left in place even when the spinnaker is stowed.
Since symmetrics are downwind sails, they are never tacked, they are only jibed. When jibing a symmetric, the pole is moved to the bow, where the sail is detached, and the opposite corner attached. This corner now becomes the windward corner. The guys are adjusted as before to set the sail angle on the new course.
To retrieve the spinnaker, the windward corner is detached from the spinnaker pole, and the guy is released. This allows the spinnaker to collapse into the shadow of the mainsail, where the foot is gathered by a crewmember. The halyard is then lowered, and a crewmember gathers the sail and stuffs it carefully into the turtle, corners out, and ready for the next deployment.
Rigging the asymmetric spinnaker
Like the symmetric, the asymmetric is often stored in a turtle, with the corners on top for easy access. Unlike the symmetric, asymmetrics have the tack attached to the bow or a bowsprit (often retractable), and have two guys attached to the clew. The head of the sail is attached to the spinnaker halyard, which is used to raise the sail. The guys are passed to either side of the forestay, one to each corner; they may be passed outside the tack of the asymmetric, or between the tack and the forestay. The guy on the downwind side of the hull is used to set the angle, and the opposite guy is left slack. Often a tack line is used at leading edge to provide adjustable tension on the luff of the spinnaker. To keep the tack near the centerline of the boat, it may be attached to the forestay with a sliding collar (often riding over the furled jib on parrel beads or similar device). Parrel beads (also spelled parral or parrell) are an element of Sailing Rigging, usually deployed at the jaws of a Gaff on a This allows the tack to slide up and down the forestay to adjust the luff tension. [1] On racing boats, the tack of the asymmetric is often rigged to a retractable bowsprit, which increases the foretriangle area and prevents interference with the jib. The bowsprit, or boltsprit, of a Sailing vessel is a pole extending forward from the vessel's prow As this trend becomes more popular in racing boats, it may result in similar adaptations to cruising boats as well. [2]
Jibing with the asymmetric is much less complex than the symmetric, due to the lack of the spinnaker pole. Much like a jib, all that is required is to change guys--however, since the asymmetric still flies in front of the forestay, the operation is reversed. The sheet is slackened, and the opposite guy is pulled in, which allows the sail to pass around in front of the forestay, and then be sheeted in on the new lee side of the boat.
Retrieving the asymmetric is similar to the process for the symmetric. The guys are released, allowing the sail to collapse to the front of the boat. The foot of the sail is then gathered, and the halyard released and the head of the sail lowered, where it is packed into the turtle.
Dousing socks
The dousing sock, "spinnaker sleeve", snuffer, or just sock, is a device used to make deploying and retrieving the spinnaker a much easier task. The sock is a long fabric tube with a ring in one end to hold it open. Since the spinnaker is stored in the sock, the first step is to set up the sock. Two lines are attached to the sock; one is attached to a bridle on the ring, for pulling the sock down, and one is up the inside, from the ring, through the top, and back down, for raising the sock; these lines may be two ends of the same line, to form a loop. The head of the spinnaker is attached the top of the sock and the ring runs down to the tack. The resulting bundle is stuffed into the spinnaker bag. The top of the sock will have provisions for attaching to the spinnaker halyard.
The spinnaker is raised as normal, but with the sock in place the spinnaker is unable to catch the wind. Once the spinnaker is raised and the guys are ready to set, the sock is raised, releasing the spinnaker. The sock remains bundled up at the head of the sail while the spinnaker is deployed. To retrieve the spinnaker, the sheet or the tack is released and the sock is pulled down, gathering the sail. The halyard is then dropped and the sail may be packed away.
Spinnaker chute
A spinnaker chute is usually a tube or aperture in the deck close to the forestay, for the launching and recovery of the spinnaker. They are most commonly found on modern dinghy designs, and updated older classes. To allow recovery of the spinnaker into the chute, one or more recovery patches are fitted to the spinnaker, to which the tail of the spinnaker halyard is attached or passed through. In Sailing, a halyard or halliard is a line ( Rope) that is used to hoist (pull up a Sail, a Flag or a yard. The spinnaker and its halyard thus form a continuous loop, passing through the chute. In Sailing, a halyard or halliard is a line ( Rope) that is used to hoist (pull up a Sail, a Flag or a yard.
If the spinnaker chute penetrates the hull and is required to be watertight, it takes the form of a hard tube sealed to the hull at both ends. If a watertight arrangement is not required, a cloth tube may be used to contain the lowered spinnaker.
Etymology of the Word
The first boat to fly a spinnaker was called the "Sphinx". The friends of Sphinx's owner jokingly referred to the sail as "Sphinx's half-acre". It was later to be abbreviated as SPINNAKER.
References
- ^ Cruising with an Asymmetrical Spinnaker. Retrieved on 04-09-2007.
- ^ J Boats. Retrieved on 2007-09-10. Year 2007 ( MMVII) was a Common year starting on Monday of the Gregorian calendar in the 21st century. Events 506 - The Bishops of Visigothic Gaul meet in the Council of Agde.
External links
- Spinnaker How-To
- Spinnaker [1], UK-Halsey's Encyclopedia of Sails: Spinnaker
- Flying a Spinnaker, Washington Yacht Club, with instructions on spinnaker use and how to avoid a broach.
- Of Carbon and Codes, a Sailing Anarchy article on asymmetric spinnaker types.
- North Sails Gennakers information page.
- Using the Asymmetrical Spinnaker, Brian Hancock, SailNet. com
- Spinnaker rigging guide at Harken. com, showing rigging for symmetric and asymmetric spinnakers.
- |ATN's spinnaker sleeve and Tacker
Dictionary
spinnaker
-noun
- (nautical) A supplemental sail to the main sail, especially a triangular one, used on yachts for running before the wind.
Dapyx Software network: MP3 Explorer | Ebook Manager | Zenithic