Digital Signal 1 - Citizendia

"DS-1" redirects here. For the guitar distortion pedal, see BOSS DS-1. The Boss DS-1 is a basic Distortion pedal manufactured by the Roland Corporation under the brand name Boss in 1978.

Digital signal 1 (DS1, also known as T1, sometimes "DS-1") is a T-carrier signaling scheme devised by Bell Labs. In Telecommunications T-carrier, sometimes abbreviated as T-CXR, is the generic designator for any of several digitally multiplexed telecommunications Bell Laboratories (also known as Bell Labs and formerly known as AT&T Bell Laboratories and Bell Telephone Laboratories) is the Research organization ^[1] DS1 is a widely used standard in telecommunications in North America and Japan to transmit voice and data between devices. For a topic outline on this subject see List of basic Japan topics. E1 is used in place of T1 outside of North America, Japan, and South Korea. In digital Telecommunications where a single physical wire pair can be used to carry many simultaneous voice conversations worldwide standards have been created and deployed Technically, DS1 is the transmission protocol used over a physical T1 line; however, the terms "DS1" and "T1" are often used interchangeably. Also, the 24 channels of traffic in a T1 line are sometimes called a T-span.

A DS1 circuit is made up of twenty-four 8-bit channels (also known as timeslots or DS0's), each channel being a 64 kbit/s DS0 multiplexed pseudo-circuit. An electrical network is an interconnection of Electrical elements such as Resistors Inductors Capacitors Transmission lines Voltage Channel, in communications (sometimes called communications channel) refers to the medium used to convey Information from a This article is about the medium access technology The name "TDMA" is also commonly used in the United States to refer to D-AMPS, which is a mobile telephone Digital Signal 0 ( DS0) is a basic Digital signaling rate of 64 Kbit/s, corresponding to the capacity of one Voice-frequency -equivalent Digital Signal 0 ( DS0) is a basic Digital signaling rate of 64 Kbit/s, corresponding to the capacity of one Voice-frequency -equivalent Time-Division Multiplexing ( TDM) is a type of Digital or (rarely analog Multiplexing in which two or more signals or bit streams are transferred A DS1 is also a full-duplex circuit, meaning, in theory, the circuit can send 1. A duplex Communication system is a system composed of two connected parties or devices which can communicate with one another in both directions 544 Mbit/s and receive 1. In telecommunications Bit rate or Data transfer rate is the average number of Bits characters or blocks per unit time passing between equipment in a data transmission 544 Mbit/s concurrently. A total of 1. 536 Mbit/s of [1] bandwidth is achieved by sampling each of the twenty-four 8-bit DS0's 8000 times per second. In Computer networking and Computer science, digital bandwidth or just bandwidth is the capacity for a given system to transfer data over a connection Digital Signal 0 ( DS0) is a basic Digital signaling rate of 64 Kbit/s, corresponding to the capacity of one Voice-frequency -equivalent This sampling is referred to as 8-kHz sampling (See Pulse-code modulation). The hertz (symbol Hz) is a measure of Frequency, informally defined as the number of events occurring per Second. An additional 8 kbit/s is obtained from the placement of a framing bit, for a total of 1. In telecommunications Bit rate or Data transfer rate is the average number of Bits characters or blocks per unit time passing between equipment in a data transmission 544 Mbit/s, calculated as follows:

$\left( 8\,\frac{\mathrm{bits}}{\mathrm{channel}} \times 24\,\frac{\mathrm{channels}}{\mathrm{frame}} + 1\,\mathrm{framing\ bit} \right) \times 8000\,\frac{\mathrm{frames}}{\mathrm{second}} = 1544000\,\frac{\mathrm{bits}}{\mathrm{second}} = 1.544\,\frac{\mathrm{Mbit}}{\mathrm{second}}.$

1 DS1 frame synchronization
2 SF framing
3 ESF framing
4 Connectivity and Alarms
- 4.1 Alarms
5 Real world use
6 Inband T1 versus T1 PRI
7 Origin of Name
8 Examples
9 Notes and references
10 See also

DS1 frame synchronization

Frame synchronization is necessary to identify the timeslots within each 24-channel frame. While receiving a stream of framed Data, frame synchronization is the process by which incoming frame alignment signals i This article is about the medium access technology The name "TDMA" is also commonly used in the United States to refer to D-AMPS, which is a mobile telephone Synchronization takes place by allocating a framing, or 193rd, bit. This results in 8 kbit/s of framing data, for each DS1. Because this 8-kbit/s channel is used by the transmitting equipment as overhead, only 1. Overhead information is Digital Information transferred across the functional interface between a user and a telecommunications System 536 Mbit/s is actually passed on to the user. Two types of framing schemes are Super Frame (SF) and Extended Super Frame (ESF). Super Frame is an older framing standard for T1s Also called D4 or D3/D4 framing In Telecommunication, an Extended Super Frame ( ESF) is a T1 framing standard, sometimes called D5 framing invented in the 1980s A Super Frame consists of twelve consecutive 193-bit frames, whereas an Extended Super Frame consists of twenty-four consecutive 193-bit frames of data. Due to the unique bit sequences exchanged, the framing schemes are not compatible with each other. These two types of framing (SF and ESF) use their 8 kbit/s framing channel in different ways.

SF framing

In SF Framing, the framing channel is divided into two channels of 4 kbit/s each. One channel is for terminal frame alignment; the second is used to align the signaling frames. The terminal frame and signaling frame bits are interleaved, rather than consecutive (they are switched in Figure 2). (correction per ANSI T1. 403 Section 7. 2 "A frame is a set of 192 digit time-slots for the information payload preceded by one digit time-slot containing the framing (F) bit, for a total of 193 digit time-slots. " Meaning the first bit of the frame is a framing bit and not the last bit. )

The terminal frame alignment channel is carried in odd-numbered frames inside the super frame and occurs with the DS0 channel synchronization. Digital Signal 0 ( DS0) is a basic Digital signaling rate of 64 Kbit/s, corresponding to the capacity of one Voice-frequency -equivalent Since the framing bits occur only once per frame, in the 193rd position, the bit placement of each DS0 can be calculated. Digital Signal 0 ( DS0) is a basic Digital signaling rate of 64 Kbit/s, corresponding to the capacity of one Voice-frequency -equivalent After the framing bit is sensed, the first DS0 timeslot is taken as the next 1-8 bits. Timeslot 2 is bits 9-16, timeslot 3 is 17-24, through to timeslot 24. See Figure 1. The Terminal frame alignment pattern is carried in odd-numbered frames, inside the super frame, and consists of alternating 1s and 0s: 1–0–1–0–1–0.

Figure 1. SF Framing bit. A single bit is added to the end of the DS1 frame to signal the start of a new frame.

Signaling frame alignment channel is carried in even-numbered frames inside the super frame and is used for signaling frame alignment. The signaling frame alignment pattern consists of a 0–0–1–1–1–0. Signaling frames are identified by the framing signal's transition from 1 to 0 and from 0 to 1; thereby frames six and twelve carry signaling information. See Figure 2.

The SF format uses bit robbing to pass signaling information. Robbed-bit signaling ( RBS) is a specific type of Channel Associated Signaling in use in North America on T1 trunks and perhaps elsewhere in the world In Telecommunication, signalling (UK spelling or signaling (US spelling has the following meanings The use of signals for controlling communications Bit robbing modifies the least significant bit in each user data timeslot twice per Super Frame. Robbed-bit signaling ( RBS) is a specific type of Channel Associated Signaling in use in North America on T1 trunks and perhaps elsewhere in the world In Computing, the least significant bit ( lsb) is the Bit position in a binary Integer giving the units value that is determining (See also A&B). The two modified frames are the sixth (A) and the twelfth (B). Using two bits, four possible signaling states can be passed in each direction (0–0, 0–1, 1–0, 1–1). In order for A/B signaling to work, the exact placement of the bits must be known by both sides. Information on the frame sequence is necessary to "pick out" the A and B bits. Channel information must also be known in order to pick out the last bit of each channel. If the proper alignment (timing) did not occur, the wrong bit could be modified or read as the robbed bit. This method of signaling is also commonly referred to as Channel Associated Signaling or CAS. See also Signalling (telecommunications Channel Associated Signaling (CAS also known as Per-Trunk Signaling (PTS is a form of digital communication signaling See Figure 2.

Figure 2. SF Framing Format (Note: Signal and Terminal frame alignment bits are interleaved)

The SF format is also known as D4 framing and D3/D4 framing format.

ESF framing

In ESF, twenty-four frames make up the (extended) super frame. ESF divides the 8 kbit/s framing channel into three segments. The frame pattern uses 2 kbit/s, and a Cyclic redundancy check (CRC) uses 2 kbit/s. A cyclic redundancy check (CRC is a type of function that takes as input a data stream of any length and produces as output a value of a certain space commonly a 32-bit integer The remaining 4 kbit/s make up an administrative data link (DL) channel. The framing pattern occupies the 4th, 8th, 12th, 16th, 20th and 24th frames. The pattern consists of a 0–0–1–0–1–1 sequence. This is the only pattern repeated in the ESF format. See Figure 3.

Figure 3. ESF Framing Format.

The CRC algorithm checks a known segment of data and adds the computed value to it. The combined data and CRC blocks are both transmitted. The receive circuitry will run the same CRC algorithm against the data portion and compare the calculation to the transmitter's CRC value. In this manner, corrupted data can be flagged as "CRC errors". The CRC checksum is passed in the 2nd, 6th, 10th, 14th, 18th, and 22nd frames. (See also Error-correcting code). In Telecommunication and Information theory, forward error correction (FEC is a System of Error control for Data transmission, whereby

The administrative channel provides a means to communicate within the DS1 stream (sub-channel). In broadcasting digital subchannels are a means to transmit more than one independent program at the same time from the same Digital radio or Digital television station Statistics on CRC errors can be requested and sent from one end to another. The data channel occupies the twelve odd numbered frames. Signaling and other information passes over this channel. Provisions in the ESF standard would allow the normal A/B bit robbed signal to be enhanced. The A/B bits can be extended to four bits (ABCD). This provides 16 distinct states. An improvement from A/B, which provides 4. To overcome incompatibility with A/B signaling, equipment repeats the A&B bits (e. g. C = A and D = B). These additional signaling bits will offer new features as equipment is built to support it.

CRC errors can be detected and counted in at least one of four different registers. The registers are for transmit (in and out) and receive (in and out). Using recovered CRC data, it is possible to segment and isolate the direction of problems.

Connectivity and Alarms

Connectivity refers to the ability of the digital carrier to carry customer data from either end to the other. In some cases, the connectivity may be lost in one direction and maintained in the other. In all cases, the terminal equipment, i. e. , the equipment that marks the endpoints of the DS1, defines the connection by the quality of the received framing pattern.

Alarms

Alarms are normally produced by the receiving terminal equipment when the framing is compromised. There are three defined alarm states, identified by a legacy color scheme: red, yellow and blue.

Red alarm indicates the alarming equipment is unable to recover the framing reliably. Corruption or loss of the signal will produce “red alarm. ” Connectivity has been lost toward the alarming equipment. There is no knowledge of connectivity toward the far end.

Yellow alarm indicates reception from the far end of a data or framing pattern that reports the far end is in “red alarm. ” Red alarm and yellow alarm states cannot exist simultaneously on a single piece of equipment because the “yellow alarm” pattern must be received within a framed signal. For ESF framed signals, all bits of the Data Link channel within the framing are set to data “0”; the customer data is undisturbed. For D4 framed signals, the pattern sent to indicate to the far end that inbound framing has been lost is a coercion of the framed data so that bit 2 of each timeslot is set to data “0” for three consecutive frames. Although this works well for voice circuits, the data pattern can occur frequently when carrying digital data and will produce transient “yellow alarm” states, making ESF a better alternative for data circuits.

Blue alarm indicates a disruption in the communication path between the terminal equipment. Communication devices, such as repeaters and multiplexers must see and produce line activity at the DS1 rate. A repeater is an electronic device that receives a signal and Retransmits it at a higher level and/or higher power or onto the other side of an obstruction In Electronics, a multiplexer or mux ( occasionally the term muldex is also found for a combination multiplexer-demultiplexer If no signal is received that fills those requirements, the communications device produces a series of pulses on its output side to maintain the required activity. Those pulses represent data “1” in all data and all framing time slots. This signal maintains communication integrity while providing no framing to the terminal equipment. The receiving equipment displays a “red alarm” and sends the signal for “yellow alarm” to the far end because it has no framing, but at maintenance interfaces the equipment will report “AIS” or Alarm Indication Signal. AIS is also called “all ones” because of the data and framing pattern.

These alarm states are also lumped under the term Carrier Group Alarm (CGA). The meaning of CGA is that connectivity on the digital carrier has failed. The result of the CGA condition varies depending on the equipment function. Voice equipment typically coerces the robbed bits for signaling to a state that will result in the far end properly handling the condition, while applying an often different state to the customer equipment connected to the alarmed equipment. Simultaneously, the customer data is often coerced to a 0x7F pattern, signifying a zero-voltage condition on voice equipment. Data equipment usually passes whatever data may be present, if any, leaving it to the customer equipment to deal with the condition.

Real world use

Before the jump in Internet traffic in the mid 1990s, DS1s were found mostly in larger businesses and telephone company central offices as a means to transport voice traffic between locations. DS1s have been and still are the primary way cellular phone carriers connect their central office switches (MSCs) to the cell sites deployed throughout a city. Network Switching Subsystem, or NSS, is the component of a GSM system that carries out switching functions and manages the communications between Mobile phones A cell site is a term used primarily in North America for a site where antennas and electronic communications equipment are placed to create a cell in a Mobile phone network

Today, many smaller companies often use an entire DS1 for Internet traffic, providing 1. The Internet is a global system of interconnected Computer networks 544 Mbit/s of connectivity (allowing for 1. 536 Mbit/s of usable traffic, and 8 kbit/s of framing overhead). However, DS1 can be ordered as a channeled circuit, and any number of channels can be reserved for non-data (for example, voice) traffic.

Many radio stations also use this technology in their broadcasting. A T1 telephone line can be used as a link to convey the broadcast audio from the studio to the transmitter/tower site, a distance that can be quite a few miles in length.

Inband T1 versus T1 PRI

Additionally, for voice T1s there are two types: so-called "plain" or Inband T1s and PRI (Primary Rate Interface). The primary rate interface (PRI is a Telecommunications standard for carrying multiple DS0 voice and data transmissions between two physical locations While both carry voice telephone calls in similar fashion, PRIs are commonly used in call centers and provide not only the 23 actual usable telephone lines (Known as "B" channels) but also a 24th line that carries signaling information (Known as the "D" channel for Data^[2]. ) This special "D" channel carries: Caller ID (CID) and Automatic Number Identification (ANI) data (commonly referred to in industry parlance as "signaling data"), required channel type (usually a B channel), call handle, DNIS info, requested channel number and a request for response^[3]. For the protein involved in the synthesis of Major histocompatibility complex II see CLIP (protein. Automatic Number Identification (ANI is a feature of Telephony Intelligent network services that permits subscribers to display or capture the Telephone

Inband T1s are also capable of carrying CID and ANI information if they are configured by the carrier to do so but PRI's handle this as a standard and thus the PRI's CID and ANI information has a much better chance of getting through to the destination. While an Inband T1 seemingly has a slight advantage due to 24 lines being available to make calls (as opposed to a PRI that has 23), each channel in an Inband T1 must perform its own set up and tear-down of each call. A PRI uses the 24th channel as a data channel to perform all the overhead operations of the other 23 channels (including CID and ANI). So even though an Inband T1 has 24 channels, the PRI can actually dial more calls faster because of the dedicated data (also called "D") channel.

Origin of Name

The name T1 came from the carrier letter assigned by AT&T to the technology. Essentially, the "T" is a part number that was assigned by AT&T. Just as there is the generally known L-carrier and N-carrier systems, T-carrier was next letter available and T1 is the first level in the hierarchy. SystemYearFrequencyCoax per cableDistance between repeatersVoice circuits per coaxL-119413 DS-1 meant "Digital Service - Level 1", and had to do with the service to be sent (originally 24 digitized voice channels over the T1). The terms T1 and DS1 have become synonymous and include a plethora of different services from voice to data to clear-channel pipes. The line speed is always consistent at 1. 544 Mbit/s, but the payload can vary greatly.

Examples

The global telephone network (also known as the Public Switched Telephone Network or PSTN). The public switched telephone network ( PSTN) is the network of the world's public circuit-switched Telephone networks in much the same way that the

Notes and references

^ "How Bell Ran in Digital Communications" September 1996, webpage: BYTE-Bell: Bell Labs scientists developed a time-division multiplexing scheme, T1.
^ Versadial, Call recording encyclopedia, last accessed 19 Apr 2007
^ Newton, H: "Newton's telecom dictionary", page 225. CMP books, 2004

Contents