In the oil and gas industry, depth in a well is the measurement, for any point in that well, of the distance between a reference point or elevation, and that point. It is the most common method of reference for locations in the well, and therefore, in oil industry speech, "depth" also refers to the location itself. By extension, depth can refer to locations below, or distances from, a reference point or elevation, even when there is no well. In that sense, depth is a concept related to elevation, albeit in the opposite direction. The elevation of a Geographic location is its height above a fixed reference point often the mean sea level. Depth in a well is not necessarily measured vertically or along a straight line.

The specification of depth

Although it is an intuitive concept, depth in a well is the source of much confusion because it is frequently not specified correctly. Absolute depth should always be specified with 3 components:

• a unit (e. g. m for metre),
• a path (e. g. MD for measured depth),
• and the reference or datum they refer to (e. g. RT for rotary table),

and none of these 3 components should ever be left implicit. An oil platform or oil rig is a large structure used to house workers and machinery needed to drill and/or extract oil and Natural gas through wells Example: the top of a reservoir may be found at 1,500mMDRT in a particular well (1,500m measured depth below the rotary table), which may be equal to 1,492mTVDMSL (1,492m true-vertical-depth below mean sea level) after correction for deviations from vertical.

Depth in a well as used in the oil and gas industry

• Well depths are implicitly "loggers' depths", unless specified explicitly otherwise (e. Well logging, also known as borehole logging is the practice of making a detailed record (a well log) of the Geologic formations penetrated by a borehole g. drillers' depth, core depth, etc). In other words, they were measured by the wireline loggers and because they are typically considered more reliable than those from other measurements, they are used as reference in the well. Well logging, also known as borehole logging is the practice of making a detailed record (a well log) of the Geologic formations penetrated by a borehole
• Depth increases in the "down" direction, so an elevation is a negative depth. There is no need to specify above or below the depth reference.

  Example: RT = -10mMDLAT

• The term "subsea" by itself should not be used as it is ambiguous. It could mean: below sea floor or bottom, below mean sea level (MSL), below lowest astronomical tide (LAT), etc.
• Differential (or relative) depths or thicknesses should generally be specified with two components at least: a unit and a path, plus any eventual specifiers to remove any possible ambiguity. No specifier should ever be left "implicit" or "understood". There are cases where a path is not needed and in fact should not be specified, because it is defined by the specifier, e. g. isochore (true stratigraphic thickness, independent of well path or inclination).
• It is important to remember that depths, whether "absolute", "relative", "true", etc, have an intrinsic uncertainty and are never really true.
• The distinction between "loggers' depth" and "drillers' depth" is becoming blurred due to the increasing use of logs acquired while drilling (LWD). At the time of writing, the common practice remains that the petrophysicists or geologists define the "official depths" in a well, and these depths are frequently different from the "drillers' depth", after various corrections, tie-ins, etc, have been applied.
• Petrophysicists and drilling operations tend to express depths with reference to the rotary table or the original drill floor; geologists tend to use a common datum such as the mean sea level; geophysicists use the mean sea level. This can introduce much confusion when a unit is not specified with all 3 components: unit, path, and reference.

Depth in practice: examples from in the oil and gas industry in Australia

• Unit: the usual unit of depth is the metre (m).
• Path: common expressions of path are measured depth (MD) - elsewhere often known as along hole depth (AHD) - and true vertical depth (TVD). Note that using TV for true vertical depth is not consistent with the use of MD for measured depth, hence the recommended TVD.
• Reference:
  • the legal datum offshore Australia is Lowest Astronomical Tide (LAT) - (Ref. 1 & 2). Note that this requirement in itself can cause difficulties as it is difficult to measure offshore and can vary greatly between locations and even with time. There is, however, an advantage to this convention: tidal corrections should always be of the same sign (negative depth), i. e. the sea level is always higher than or equal to LAT.
  • A commonly used alternative is Mean Sea Level (MSL).
  • A datum used in the past was Mean Indian Spring Low Water (MILSW). It is comparable to, but not exactly the same as, LAT.
  • Common references used in operations include: Rotary Table (RT), Drill Floor (DF), Kelly Bushing (KB), Sea Bottom (SB), Ground Level (GL).

Whichever combination of unit, path, and reference can be used, as long as they result in fully specified, unambiguous depths.

Figures

Fig. 1: The specification of depths

Fig. 2: Differential depths: reservoir thickness, isochor, isopach

Specification of an absolute depth: in Figure 1 above, point P1 might be at 3207mMDRT and 2370mTVDMSL, while point P2 might be at 2530mMDRT and 2502mTVDLAT.
Specification of a differential depth or a thickness: in Figure 2 above, the thickness of the reservoir penetrated by the well might be 57mMD or 42mTVD, even though the reservoir true stratigraphic thickness in that area (or isopach) might be only 10m, and its true vertical thickness (isochore), 14m.

External references

• Lowest Astronomical Tide (LAT)
  
• Seas and Submerged Lands Act 1973 (Australia)
• Log Data Acquisition and Quality Control, Ph. Theys, 1991, Editions Technip